cardiagnostic.us | Tag Archives: ICOM A2

Tips on How to Set Up New BMW ICOM A2 USB WiFi

Posted on September 26, 2018 by wp-admin Posted in BMW ICOM .

The WiFi setting for old and new version BMW ICOM A2 is different. Please kindly read this BMW ICOM A2 USB WiFi Setup manual before you use WiFi function
1. Plug USB-WiFi adapter to the USB connector of your laptop

2. Disconnect your laptop from network, turn off all WiFi on your laptop, also do not connect the device to laptop currently.
3. Carefully check you have finish all the prepare working. Press”start” button to boot the laptop
4. Booting laptop, once confirm whether you turn off all internet or disconnect all lan cable

The DWA-131 is our USB-WiFi,no need turn off.”X” is normally, do not worry
5. Boot BMW ICOM A2 software, click WiFi for ICOM

6. You can connect the BMW diagnostic tool ICOM A2 interface to your car right now, wait about 20-30 mintues, the Wlan light on device will not flash or flash slow. That means the communication between USB WiFi and ICOM WiFi is ok

7. It’s time to click diagnosis or programming software

Click”ok”

The ways about how to update 2015.06 Version BMW ICOM A2 Firmware

Posted on September 18, 2018 by wp-admin Posted in BMW ICOM .

when you need to update bwm icom A2 firmware , you need to according to the steps as following:
1. Use Network cable to connect ICOM A2 with a computer, charge ICOM A2 with 12V power adapter or connect ICOM with the BMW vehicle.
2. Open IE Internet Exploer, browse http://169.254.92.38:60080/, log in with username/password: root/NZY11502.
3. Click “Update Firmware”, you will see ICOM firmware version information.
4. Choose file “ICOM-BootImage-01-13-00.bin”, set image type to SYSTEM, click “Send the file”.
5. When it pops up “Write the image file to the flash?”, click “Yes”, then ICOM indicator light will turn red.
6. When it pops up “The SYSTEM IMAGE update was successfull”, click “Update Firmware”.
7. Choose “ICOM-ApplicationImage-01-18-00.bin”, set image type to APPLICATION, click “Send the file”, it will take several minutes since the file is a little bit large.
8. When it pops up “Write the image file to the flash?”, click “Yes”, then the ICOM indicator light will turn red for the second times.
9. When it finish upgrading, click “reboot” to reboot the computer.
Important Note:
1. Setting up your computer to obtain an IP address automatically
2. Firstly choose the smaller file “ICOM-BootImage-01-13-00.bin” , then set image type to SYSTEM;
Secondly choose the bigger file “ICOM-ApplicationImage-01-18-00.bin”, then set image type to APPLICATION.

How to solve the problem that BMW Icom A2 A3 host can’t be connected?

Posted on June 4, 2018 by wp-admin Posted in BMW ICOM .

Aftre the BMW ICOM host is connected to the car via a 16PIN connector, and the other side is connected to the computer via a network cable. Your BMW ICOM lan and system lights will light up. As follows:

But at this moment,the host can’t be found in the computer.As follows:

When meeting the problem,please update your BMW ICOM firmware as the following method:

1.Please connect BMW ICOM to the computer vith network cable and power on the BMW ICOM with a 12V power adapter.

2.Open the website address http://169.254.92.38:60080/by IE browser, username:root password:NZY11502.

3.Click the “update firmware”，it will show ICOM firmware version information.

4.Choose the file ICOM-BootImage-01-11-01.bin,set image type to SYSTEM，click “Send the file”.

5.When shows “Write the image file to the flash?”，click “Yes”,then ICOM light turns red.

6.When shows “The SYSTEM IMAGE update was successfull”，click “Update Firmware”.

7.Choose the file ICOM-ApplicationImage-01-15-01.bin，set image type to APPLICATION.Click “Send the file”.It will takes a few minutes because of a little large file.

8.When shows “Write the image file to the flash?”，click “Yes”，then the ICOM light turns red for the second time.

9.It is all normal,click “reboot”.

After finishing these steps,please connect again,the ICOM host will be found in the computer,as follows:

See more click:http://www.autonumen.com/

How to use 2017.07 version BMW ICOM A2 ISTA for diagnostic car ?

Posted on May 29, 2018 by wp-admin Posted in BMW ICOM .

BMW ICOM A2+B+C latest software version is 2017.07. ISTA-D 4.05.32 ISTA-P 3.61.5 VIN: 2017.05 Now we show you how to use BMW icom A2 and ISTA D software ,check all car module status and delete fault code history. the operation steps is easy.

steps 1: connect your ICOM A2 main unit with your car, then open ISTA-D 4.05.32

You need to do a vehicle test firstly.

go to ” vehicle information ” -” control unit free”-“start vehicle test”

click” yes” , then start vehicle test

steps 2: when finish vehicle test. the faulty module will be display in yellow or red. yellow means there is a error memory, red means no response.

if you see there are all is green, it means not problems at all.

press the “display fault memory ” button to check the error code.

steps 3: click” vehicle management”-“troubleshooting” – ” fault memory”

you can see the error description with error code. double click every item, you can see detail description of phenomenon.

just click” delete fault memory” to clear the faulty memory

BMW ICOM software support Multi-language available in diagnosing, programming and TIS diagram circuit: American English, British English, German, Spanish, French, Italian, polish, Portuguese, Turkish, Czech, Swedish, Dutch, Indian, Greek, Russian, Simplified Chinese, Traditional Chinese, Japanese, Korean and Thai.

See more click:http://www.autonumen.com/

Best quality BMW ICOM A2 Diagnostic & Programming in good price

Posted on May 7, 2018 by wp-admin Posted in BMW ICOM .

BMW ICOM A2+B+C Diagnostic & Programming Tool 2013 New arrival!

BMW ICOM A2+B+C support BMW cars till 2013 year. This tool Support BMW & MINI full system diagnose and offline programming.It is professional diagnostic tool for BMW Brand.

BMW ICOM A2+B+C Functions:
A2 – OBD diagnostic supporting MOST, D-CAN and K-CAN protocols
B – diagnostic via MOST bus, and have connection to A-interface via USB connection.
C – 20-pin cable for old models.

Compare with old version BMW ICOM,what is the different?

1.The modified BMW ICOM A2 for vehicles with OBD access receives a significantly more powerful processor and more storage capacity.Robust aluminium case will help to avoid damage when using in harsh environments.

2.To protect the MOST connector, the BMW ICOM B for vehicles with optical MOST access will be equipped with a soft cover made of rubber instead of the former plastic cap.

3.The BMW ICOM C for old series with a diagnostics socket will be additionally equipped with an approx. 20 cm long cable, which facilitates the connection of the BMW ICOM A2 and makes storage in the engine compartment easier.

AUTONUMEN.COM provide New BMW ICOM A+B+C A2 Diagnostic & Programming for both hardware and software. New ICOM A2 with external HDD fit All Computer only sell 499USD.
If you are interesting in BMW ICOM diagnostic tool,welcome you to place an order.

How to Using BMW ICOM A2+b+c to program BMW F-Series chassis models

Posted on December 9, 2017 by wp-admin Posted in BMW ICOM .

Using BMW ICOM A2+b+c to program BMW F-Series chassis models

* Programming Control Unit

* Set Code Control unit

Control unit measures can be selected as follows:

* Click on the control unit under the tab “Control Unit Tree”

* Under the “TAB Edit Control unit”, either by direct selection or by clicking on the control unit.

Menu “Programming”

To execute the vehicle programming/setting code, do the following:

* Use ista/p to read vehicle data.

After you create a new dialog, display the tips for “dialog preparation”

* Follow the tips, record when necessary, confirm button “OK”

Show the dialog box “whether the control unit has been replaced”

* Confirm button “No”, exceptions see “replace (update) control unit”

Establish a connection with the vehicle:

The vehicle details are displayed after the specified associated environment has been successfully identified. Displayed under Menu “Programming”.

1 Menu “Programming”

2 Integration Level (actual), showing the vehicle’s current integration level

3 Open code status, used in vehicles or necessary opening code status

4 progress bar, showing the process of determining the action plan

5 final processing, showing ProgMan or ista/p version, through which the vehicle is finally processed.

6 Integration Level (factory), showing the integration level of vehicle production

7 Tab “Vehicle Details”

Tip: If there is no action for the specified associated environment, the button “Confirm Action plan” is not activated.

tab “Control Unit Tree”:

The control unit tree according to the topological structure, the image displays the control unit which the vehicle installs. Each control unit is displayed with the corresponding bus connection. The combined control unit is displayed in a light blue area.

1 Menu “Programming” 2 Tab “control Unit Tree”

3 Button “Choose the total set code”,

Vehicle Total Setting Code selected

4 Button “Cancel action”, the measures determined in the associated environment are deleted

Tip: You can directly perform measures that are not affected by the integration level (such as hard drive upgrades) without writing to the integration level. “Cancel action” on this confirmation button. Delete all measures determined by the associated environment. Integrated level-related control unit measures may not be selected manually.

tab “Edit Control Unit”:

1 tab “Plan processing”

2 programming, programming the control unit

3 Code, set code for control unit

4 replacement, replacement (update) control unit

5 replacement post-processing, subsequent processing of replaced (updated) control units

The measures available to the control unit are different. Depending on what measures are defined, the control unit may vary.

Select the control unit and the screenshot after the” tabs action” list:

1 Tab “Action list”

2 Icon “Measure failed”

3 icon “Action Missing Prerequisites” 4 Icon “Warning”

5 icon “measure Success” 6 Icon “measures in progress”

7 Icon “Planned software measures” (for example, set code)

8 icon “Planned hardware measures”

Select the tab “action list” to display planned measures that include the appropriate status.

Select the control unit, the screenshot after the TAB “control unit Information”:

1 Menu “Programming”

2 Tab “Action list”

3 button “Determine Action plan”

The “action list” is a summary of the form of the planned action table. These measures are also shown in the “Action plan”. Also displays hints about the control unit (for example, the control unit is not programmable).

Menu “Vehicle”:

By switching to the menu “vehicle” You can add the following measures to the plan:

* Modification and retrofitting, see “refitting and retrofitting”

* Vehicle operation (HDD upgrade, see “Upgrading Navigation System Map data”).

xt-transform:none;font-style:normal;font-size:9.5000pt;mso-font-kerning:0.0000pt;background:rgb(255,255,255);mso-shading:rgb(255,255,255);” > after the TAB “control unit Information”:

1 tab “Refit” to show available modifications and retrofitting

2 Tab “Vehicle operation”:

* Upgrade navigation system map data (HDD upgrades)

* Input Vehicle Task

* Select the total set code

3 Menu “Vehicle”

To select other measures (programming, setting code), switch back to menu “programming”.

:none;font-style:normal;font-size:9.5000pt;mso-font-kerning:0.0000pt;background:rgb(255,255,255);mso-shading:rgb(255,255,255);” >* Modification and retrofitting, see “refitting and retrofitting”

* Vehicle operation (HDD upgrade, see “Upgrading Navigation System Map data”).

xt-transform:none;font-style:normal;font-size:9.5000pt;mso-font-kerning:0.0000pt;background:rgb(255,255,255);mso-shading:rgb(255,255,255);” > after the TAB “control unit Information”:

Best Quality BMW ICOM A2 +B+C Diagnostic & Programming TOOL

BMW ICOM A2 With WIFI And Rheingold ISTA Enigneer Tool

Posted on October 19, 2017 by wp-admin Posted in BMW ICOM .

BMW ICOM A2 is new generation BMW Scanner which instead of its previous version BMW ICOM A+B+C for diagnose and program BMW group vehicles . The unit includes the BMW ICOM A2+B+C (with WIFI function) and 500GB HDD contains latest Rheingold ISTA D/P and Engineer tools(INPA,E-SYS,ETK,NCS and so on.

1. Top Quality BMW ICOM A2+B+C With WIFI connection function.

2. With Latest 500 GB hard driver contains latest Rheingold ISTA D/P and Enigneer Tool.

3. The hard drive can be installed on 95% laptop with Intel CPU I3I5I7 and 4GB Ram.

4. Software version is 10.2015 ISTA-D (3.51.13) + ISTA-P (3.56.3.002) + Engineer Tool.

PLS NOTE:

No Network And Also No Connection With The Original Server When You Use The Rheingold BMW ICOM Software HDD, Otherwise It Is Will Be Damaged,And Need You Send Back For Repair.

The advantages of BMW ICOM A2+B+C ISID Diagnostic Tool

1.Faster processor and bigger storage for better expression.

2.Robust construction makes it can works in complicated environment.

3.The Part B of A2 will be covered by a soft gap, it is for avoiding dust & oil & water.

BMW E46 DME Update by WinKFP Guide+ Import Daten files Q&A

Posted on October 18, 2017 by wp-admin Posted in BMW ICOM .

This blog is a step-by-step guide for Autonumen.com BMW E46 DME Update DIY by WinKFP. First to download BMW INPA EDIABASWinKFP BMW Coding Tool NCS Expert all programs you need!

How to update BMW DME Module using WinKFP easily?
Tool needed:
BMW ICOM A2 or cheap INPA K+DCAN Cable

Before you start, you should firstly import the daten files cirrectly! Or the update will be fail.
Check below case:
I have run into an issue after installing WinKFP 5.3.1
I have INPA running ok, import the SGDA (.IPO files), ECU (.PRG files) and assembly line data. After choosing “Comfort Mode” -> “Update ZUSB”, there is nothing on the “ECU family”. It’s empty.
Do I import the files incorrectly? Any solution please?

Solution 1. You can use WinKFP Tool to import the daten files. Here is a guide for your checking.

https://mega.nz/#!5ohmVaZY!gsNV0nRe4_QJCv19clRPwFOHH7mgcsShb8MNP6ksq54

Solution 2. You can also import daten files via BMW coding tool. It’s tested working.

Steps to Update BMW DME using WinKFP:
Connect BMW E46 car with laptop via BMW ICOM or BMW INPA K+DCAN.
Open WinKFP.
Click F1 button “Comfort mode”.
Click F3 button “Update ZUSB” and you get a box displaying ECU families.
pull down the drop-down list to choose the ECU family (MDS42 for MS42, MDS43 for MS43, MDS451 for MS45.1, etc.), click OK.

Click F4 button “Enter VIN” and input car VIN number.
Click “Done”, which goes back a screen.
Click F3 button “Prog ZB-Update”, and you should get a box that displays your current ECU version and suggests an update version.

Click “Yes” and you get another box asking permission to program ECU.
Click OK and the update begins.
It takes about 10-15 minutes to complete for MS42/43, 45 minutes for MS45.1.
At the end it tells you that the programming was OK.
Reset adaptation values using INPA or PA Soft after it is done.

How to run BMW ICOM A2 with E-SYS

Posted on October 13, 2017 by wp-admin Posted in BMW ICOM .

It is possible use the icom a2 to work in the e-sys??
Yes, just lock it with EasyConnect, obd_ab625 and then insert your ICOM IP in ESYS connection manager.

Here are the steps:
You have to lock/check the ICOM IP in ISTA-D so E-Sys can use it. Therefore you need a tool like EasyConnect or iToolRadar.

Connect the BMW ICOM A2, turn the ignition on, start f.e. iToolradar. Now you can see the connection from the ICOM (normally on 169.154.92.38), mark it and click on reserve
(in EasyConnect is different but as easy as itoolradar).

Start E-Sys, choose the target (f.e. F010) and click on “connection ICOM/Ethernet”. Type the IP address (here 169.254.92.38), the port is 50160, so the result should be tcp://169.254.92.38:50160.

Connect and have fun.

Note: TRY ON YOUR RISK. The instruction via pictures is kind of different that via words, especially ICOM IP setup. Both can be tried.

BMW ICOM A2 Solid Drive SSD black screen solution

Posted on October 12, 2017 by wp-admin Posted in BMW ICOM .

Problem:

When install BWM ICOM A2 Super ICOM SSD (Solid Drive) on Lenovo ThinkPAD laptop, the windows turns to black screen.

Solution
1. Set computer/laptop to achi mode
2.Make sure your computer time is your local time.
3.PC has at least 4GB RAM

Support all SATA format laptop or computer which has 2GB(Recommend 4GB) memory.
Laptop Hardware requirements:
CPU: Intel Celeron 2.0 and above (i5 Recommend)
RAM: 2Gb and above (4Gb Recommend)
USB: 2.0 and above

Better use Dell D630 laptop.

http://www.autonumen.com/goods-4479-BMW+ICOM+A2++Diagnostic++Programming+For+BMW+ICOM+A2BC.html