cardiagnostic.us | Category Archives: MB Star

Sloved!Some Mercedes-Benz can’t be tested with MB Star C4/C5 MB SD Connect Compact C4/C5 Diagnosis tool

Posted on October 15, 2019 by wp-admin Posted in MB Star .

Recently, there are many customers who have reflected,the following tips appear when testing some Mercedes-Benz cars with V2018.09 MB STAR C4 SD Connect Compact Diagnosis tool:

We first checked the hardware of MB STAR C4/C5 and found that the hardware works normally. The problem should be in the software section.

One of the customers in Hong Kong reported that after the software upgrade to V2018.09, the Mercedes-Benz C-series car could not be connected, and the same prompt appeared above.

Model of his car: Mercedes-Benz C320 chassis W204 2015.

We looked at the diagnostic interface provided by the customer and found that there is a hardware icon for MB STAR C6 in the upper right corner of the xentry software interface, as follows:

It turns out that the customer has set the hardware mode error to C6 mode.

When the customer uses the Mercedes-Benz diagnostic tool MB STAR C4 or C5, the corresponding hardware mode must be set to C4 in the software. Your MB STAR C4 or C5 can work normally.

If you set the wrong hardware mode, there will be some Mercedes-Benz models that cannot be diagnosed or some features that cannot be used.

How to set your MB STAR C4 or C5 hardware mode:

1.Open your MB STAR C4 or C5 software

2.Double click ConfigAssist icon.

3.Select the hardware mode:

3.1 If the Mercedes-Benz diagnostic device you are using is MB STAR C4 or C5, please select SD connect, as shown below:

3.2 If the Mercedes-Benz diagnostic device you are using is MB STAR C6, please select xentry diagnosis VCI, as shown below:

3.3 If you choose xentry diagnosis VCI suitable for MB STAR C6, the hardware icon of C6 appears in the software interface, as follows:

3.4 If you choose SDconnect mode for MB STAR C4 or C5, the C6 hardware icon of the software interface will disappear, as follows:

When your MB STAR C4 C5 C6 hardware mode is set up correctly, your device will work properly.

If your device hardware is normal, the hardware mode settings are also correct. But there are still some Mercedes-Benz cars that can’t be tested, that is, your Mercedes-Benz software permissions issue.

Because MB STAR C4/C5/C6 software also has usage rights, some functions must be authorized before they can be used.

If you want to know more about Mercedes-Benz MB STAR C4/C5/C6, please contact us. www.autonumen.com

V2017.12 MB SD Connect C4/C5 BMW ICOM/ICOM A2 A3 HDD Setting

Posted on October 8, 2019 by wp-admin Posted in MB Star .

Customer’s problem:
We had purchased one set MB SD connect C5 with internal HDD from obd2tool, We really appreciate the faster shipment, all is well packed dhl week quickly received. But when we install the HDD to our computer, we have blue screen and doesn’t access to computer windows. We are wondering if we get the broken HDD……

Our Answers:
The BMW ICOM ICOM A2 A3 or MB STAR C4 C5 drives we assign to our customers are generally AHCI-mode hard drives with SATA port.

If your laptop BIOS is not set to the same hard drive mode (AHCI mode), if you connected to our hard drive to your computer, there will be a blue screen or can not find the hard drive.Please make sure your HDD is set to AHCI in the BIOS.

To check this you turn the laptop on and press F2, it will enter the BIOS. Now go to “ONBOARD DEVICES” or “SYSTEM CONFIGURATION” then go to “SATA OPERATION” press enter and make sure its set to AHCI not ATA or any other option.

Please have a minimum of 2GB of ram/memory in your laptop, a lot of people only have 512mb or 1gb, it is OK but the new system may run slow and its recommend to really have 4GB ram, but 2GB also can be enough.

– We can supply Laptop + Software all ready for you.
– We can supply FULL package C4 SD + Laptop + Software for you. MB Star Diagnostic Tools
– We can carry out some C4 SD repairs.
– Remote installations available (if you supply the correct HDD size and install the correct Windows OS).
– Teamviewer remote support available.

Mercedes BENZ C5 SD Connect Xentry Tab Kit Technical Support

Posted on September 30, 2019 by wp-admin Posted in MB Star .

Why MB Star Diagnostic tool is so well-received by thousands of users, its technology and quality is developed after lots of experiments and improvement. Recently, we mbstar shop website provide a new Star diagnosis bundle, Mercedes BENZ C5 SD Connect Xentry Tab Kit( Newest Mercedes BENZ Diagnostic Tool;Original second hand Mercedes BENZ C5 SD Connect Xentry Tab Kit;With original software and tablet kit;Support BENZ latest protocol)

BENZ C5 SD Connect Diagnostic Tool Description:
Mercedes Benz C5 Xentry Connect diagnostic interface, produced by French ACTIA Company and equipped with Panasonic Xentry-Tab, can test Engine / Transmission / air conditioning /SRS/ABS/ anti-theft system and OBD-II system.
Benz C5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
BENZ C5 SD Connect Diagnostic Tool Feature:
Efficient diagnostic program and complete vehicle database
Simple and easy-to-use user interface (UI)
High-performance Tab with 4G memory and 13.3 inch LCD touch screen
Advanced upgraded VCI+ communication inter
Support Wired/ wireless connection
Cover all new Mercedes Benz models.
BENZ C5 SD Connect Diagnostic Tool Configuration parameters
A full set of kit configuration
1.Panasonic newest widescreen tab.
2.The original Xentry-Connect by ACTIA
3.Mercedes Benz OBD2 diagnostic cable
Panasonic widescreen Xentry-Tab technical parameters:
666

1.OS: windows 7
2. ultimate CPU:4G
3.Hard disk memory: 250G
4.13.3inch touch screen

Xentry-Connect (VCI+) Technical Parameters:

1.OS: Windows Embedded Standard 7(32bit)
2.Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
3.Memory: 4G hard disk with 256GB SSD
4.Display: 128*64 PX
5.Battery: 40 minutes (When CPU capacity to 60%)
6.Weight: 1.9KG
7.Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ

MB Star C6 Benz Diagnostic Tool with DOIP&AUDIO Function

Posted on September 24, 2019 by wp-admin Posted in MB Star .

VXDIAG MB SD Connect C6 MB Star C6 Benz Diagnostic Tool with DOIP&AUDIO Function Better than MB STAR C4/C5

Original VXDIAG For XENTRY Diagnosis VCI VXDIAG For XENTRY Diagnosis DoIP Pass Through Interface

VXDIAG For XENTRY Diagnosis VCI is the latest interface for For Mercedes & SMART vehiclescan replace Star C4/C5. VXDIAG For XENTRY Diagnosis VCI acts as a Pass-through Interface, also called Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the VXDIAG For XENTRY software loaded on a PC. CnAutotool.com VXDIAG MB Star C6 Multiplexer MB SD Connect C6 Benz Diagnostic ToolWith DOIP Functions And V2018.12 MB Star C6 Download Software.

VXDIAG MB SD Connect C6 XENTRY Diagnosis VCI Features:
1. VXDIAG For XENTRY Diagnosis VCI can be used for all model series of For Mercedes For Benz vehicles
2. VXDIAG For XENTRY Diagnosis VCI support DoIP, cover more functions during SCN Coding than SD C4/C5
3. VXDIAG For XENTRY Diagnosis VCI functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
4. VXDIAG For XENTRY Diagnosis VCI Diagnosis updates no longer necessary – firmware updates required on rare occasions
5. VXDIAG For XENTRY Diagnosis VCI does not need a power supply unit for external power supply
6. VXDIAG For XENTRY Diagnosis VCI Handy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
7. Engines (All Gasoline & Diesel Systems)
8. Transmissions and Electronic Selector Modules
9. Airmatic and Active Body Control Suspension Systems
10. Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
11. Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
12. Drive Authorisation System
13. Sam (Signal Acquisition) Modules
14. Electronic Ignition System (EIS)
15. Pneumatic System Equipment and ATA functions
16. Air Conditioning / climate control Systems
17. Instrument Cluster
18. Tyre Pressure Control
19. Parktronic System
20. Keyless Go
21. D2b Command & Audio Gateway (D2B and MOST networks)
22. TV Tuner
23. Headlamp Range Adjustment
24. Seat Electronics
25. Rvc, RST & Vario Roof modules
26. Automatic Clutch System ACS
27. M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
28. Assyst & ASSYST + systems

Difference Between Star Diagnosis Star C4 and Star C5

Posted on September 24, 2019 by wp-admin Posted in MB Star .

Star diagnosis mb star c4 and C5 all all for Mercedes Benz. One of Autonumen.com customers want to buy a star diagnosis mercedes for programming Mercedes and confuse now.Autonumen.com tell the difference between mb star c4 star diagnosis mercedes c4 and c5.

Review from Autonumen.com customer:

I use xentry 09.2016 bought from Autonumen.com works great, you can find premade acronis images and installation version here, just search for Xentry.
It’s good for trouble shooting and coding.
In some cases online scn coding requires a MB server connection.
You find members here that offer scn coding via team viewer.
Vediamo is also available I have not used it a lot but it lets you code and program on a deeper level.

Both sd connect c4 and c5 work good in coding and programming Mercedes Benz.but as for china clones, i prefer sd connect c4, c5 just in c4 casing

MB SD Connect C5 vs. SD Connect C4:

The software of SD Connect c5 is the same as that of SDconnect c4, but the hardware of SD C5 is better and stable than SD C4

1. The host communication connection end USES from design, to avoid inadvertently fall in the normal use of the communication port to connect and communication failure, etc.

2. DC 12 v power supply design/host upgrades to avoid the battery installation/battery voltage instability/host can’t enter the shutdown state, etc, caused by the motherboard and rapid aging of the battery.

3. The host CPU radiator surface and perfectly fit alloy shell, good heat dissipation effect. Equipment running smoothly, don’t crash.

4. The host USES the tamper clasp, should to avoid fragile warranty sticker damage caused by the warranty disputes.

5. Host wi-fi protected the upgrade for PC plastic shell, solid quality does not affect the wi-fi signal.

6. OBD main telecommunication lines connected to the host end upgraded to VGA15 industrial-grade connector.

7. Network upgrade for gigabit connections/pure copper wire core/double layer aluminum foil/woven mesh/silica insulation material. Gigabit communication Against interference/pulling open circuit / / fracture in low temperature.

Conclusion:

SD connect c4 wins!
It works good in basic obd2 diagnostics, SCN coding, ECU/key programming online or offline on Mercedes cars, truck and Smart as well.

Focus On OBD Tool Since 2008

Wechat/WhatsApp:(+86)15815514521

Email:service@autonumen.com

Website:www.autonumen.com

Before Buying MB STAR C6,What Should We Know?

Posted on September 17, 2019 by wp-admin Posted in MB Star .

Mercedes Benz C6 OEM Xentry diagnosis VCI DOIP Pass thur interfac is the latest interface for For Mercedes & SMART vehicles can replace Star C4/C5. XENTRY Diagnosis VCI acts as a Pass-through Interface, also called MB Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the XENTRY software loaded on a PC.

Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface Benz C6 Overview:

Compatible Software: VXDIAG For XENTRY/Das Software

Support Vehicle: Mercede For Benz & Smart vehicles

DoIP: Support DoIP

Functions: Star Diagnostic & programming (SCN Coding)

What is DOIP?

DOIP is ISO 13400 diagnostic protocol

ISO 13400-1:2011 describes the general use cases and communication scenarios which are covered by an Internet Protocol-based vehicle communication standard. Each use case drives specific communication capabilities of the vehicle communication interface, for instance in order to be interoperable in an existing computer network.

The diagnostic communication over Internet Protocol (DoIP) protocol supports the standardized service primitive interface as specified in ISO 14229-2.

The descriptions in ISO 13400-1:2011 cover different application layer implementations, such as:

enhanced vehicle diagnostics (system diagnostics beyond legislated functionality, non-emissions-related system diagnostics);

WWH-OBD (World-Wide Harmonized On-Board Diagnostics) as specified in ISO 27145-2 and ISO 27145-3.

The mercedes Land Rover JLR all use this new Diagnostic Protocol now.

Where need DOIP device?

when we test mercedes new car like w222 w205

In Audio\Comand section you can find DoIP test page.

If cable is DoIP you will see green mark that DEVICE is Ok.

Xentry will prompt you that other device must carry yellow marks.

Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 Features:

Can be used for all model series of For Mercedes For Benz vehicles
Support DoIP, cover more functions during SCN Coding than SD C4/C5
Functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
Diagnosis updates no longer necessary – firmware updates required on rare occasions
Does not need a power supply unit for external power supply
Dandy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
Engines (All Gasoline & Diesel Systems)
Transmissions and Electronic Selector Modules
Airmatic and Active Body Control Suspension Systems
Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
Drive Authorisation System
Sam (Signal Acquisition) Modules
Electronic Ignition System (EIS)
Pneumatic System Equipment and ATA functions
Air Conditioning / climate control Systems
Instrument Cluster
Tyre Pressure Control
Parktronic System
Keyless Go
D2b Command & Audio Gateway (D2B and MOST networks)
TV Tuner
Headlamp Range Adjustment
Seat Electronics
Rvc, RST & Vario Roof modules
Automatic Clutch System ACS
M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
Assyst & ASSYST + systems

Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 Summary:

Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 (Vehicle Communication Interface) multiplexer serves as the interface to the vehicle when performing diagnosis and repairs, and programming electric and electronic on-board vehicle systems.

The Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 does not have its own PC core, battery, fan, or display. It is operated using the VXDIAG For XENTRY Diagnosis Pad via WLAN or a USB cable connection.

Notice :

1.Please install the 500GB HDD on laptop above 4GB Memory and I5 CPU, and use it on one laptop only. If change laptop, software may get broken and need to ship HDD back to us to copy software again.

2.ThisMercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 can/’t support All Key Lost,needs one key at least

MB star c5 update newest software 2017.05

Posted on September 17, 2019 by wp-admin Posted in MB Star .

mb star c5 software update the newest version 2017.05, mb star c5 is update version of mb star c4, it including all the mb star c4 function .

mb star c5 Support Mercedes Benz Cars After Year 2000

it support vehicle list as following:

Passenger Car Support List:
A(176), A(169), A(168), B(246), B(245), CLC(117), C(204) C(203), C(202), 190(201), E(212), E(211), E(210), 124(124), S(222), S(221), S(220), S(140), S(126),
E(207), CLK(209), CLK(208), CLS(218), CLS(219), CL(216), CL(215), CL(140) SLK(172), SLK(171), SLK(170), SL(231), SL(230), SL(129), SL(107), SLS(197),
M(166), M(164), M(163), G(463), G(461), E(212), E(211), E(210), 124(124), S(222), S(221),S(220), S(140), CLK(209), CLK(208), CLS(218), CLS(219), CL(216),
CL(215), CL(140), SLK(172), SL(231), SL(230), SL(129), SL(107),SLS(197), M(166), M(164), M(163), G(460), GL(164), GLK(204), R(251)

Van Support List:
MB 100(631), T1, SprinterIII, SprinterII, SprinterI, Sprinter900, Citan, Vito(639), Vito(638), V(638), Viano(639), T2, Vario, Vaneo(414)

Truck Support List:
Actros963/4, Actros2,3, AtegoIII, AtegoII, AxorII, Eonic, Zetros, Actros, Atego Light, Atego Heavey, HPN M96, Atron, HPN M2000, SKL, FSK, Further model series

Unimog Support List:
U20, UGN, UHN

Bus Support List:
TRAVEGO, INTOURO, INTEGRO, CITARO, CAPACITY, CITO, TOURISMO, O350/O403, CONECTO, O404, O405-O408,
Minibus, OC500, TOURO, TOURINO, MBC, MULITEGO, O500, O500/OH, OH, OH368, OF, OF384, LO, O400,
FURTHER MODEL SERIES

Super Sports Car Support List:
SLR(199)

VXDIAG MB SD Connect C6 Benz Diagnostic Tool MB Star C6 Multiplexer With DOIP Functions And V2018.9 MB Star C6 Download Software

Posted on September 10, 2019 by wp-admin Posted in MB Star .

VXDIAG MB SD Connect C6 Benz Diagnostic Tool MB Star C6 Multiplexer With DOIP Functions And V2018.9 MB Star C6 Download Software

VXDIAG MB Star C6 Multiplexer features with same functions as Original Mercedes Benz Xentry diagnosis VCI. MB SD Connect C6 Benz Diagnostic Tool With DOIP and AUDIO Function Better than MB STAR C4/C5. autonumen VXDIAG MB Star C6 Multiplexer MB SD Connect C6 Benz Diagnostic Tool With DOIP Functions And V2018.9 MB Star C6 Download Software.

VXDIAG MB Star C6 Mercedes Benz Xentry Diagnosis VCI Original MB SD Connect C6 Benz Diagnostic Tool with DOIP&AUDIO Function Perfect replacement MB STAR C4/C5

VXDIAG Benz Star C6 for Xentry diagnosis vci from autonumen highlights:

1.Also called Star C6 Multiplexer, MB Star C6 VCX interface supporting MB Star C4, SD C5 function, performing diagnosis, repairs, program electric and electronic on-board vehicle systems.

2. VXDIAG MB Star C6 Mercedes Benz Xentry Diagnosis VCI from autonumen Support DoIP, cover more functions during SCN Coding than SD C4/C5. Even can turn on hidden features.

3. Same Star Diagnostic & programming (SCN Coding) functionas ORIGINAL DIAGNOSIS VCI

Allow to pay to add any of these car brands: GM, Ford, Mazda, Toyota, Honda, LandRover, Jaguar, Subaru, Volvo, VW and For Porsche

vxdiag Benz Star C6 for Xentry diagnosis Details

Version:

V2018.9 MB Star C6 Download Software from autonumen, it means works with the Mercedes Benz & Smart cars up to 2018 year.

VXDIAG Benz C6 Mux from autonumen Languages:

22 languages in total.

Some problem when you operate the MB Star C4

Posted on September 10, 2019 by wp-admin Posted in MB Star .

So many customer meet some problem when they operate MB Star C4.If you also have some problem .pls do not worry about that .you could tell us what is happened and send the picture which step could not work .Our engineer will solve that one by one for you .

Here Let us to show some problem we often meet then how to solve that as following :

Q1: The MB STAR C4 could work with the window 7?
A1: Although the moveable hard disk version is compatible with WIN7, better Professional version. But we suggest you not use WIN7, 90% sdc4 software get broken because of the usage of WIN7.

Q2: When you operate the mb star c4 but that the Screen become blue after insert SD C4 Dell D60 hard disk into the computer and open it.
A2: Pls note : you need make sure your Dell D630 computer is integrated video card and with 1GB memory, because the D630 of discrete video card is easy to have blue screen or shutdown and restart, restart and shutdown.

Q3:When you operate that .if appear the problem as following picture ?

A3: Pls do not worry about that .you need activate that .and then we will send the the Xentry deverloper file then you will activate that is ok .

Here i wont list more one by one here ,if you meet any problem when you operate the mb star c4 ,pls contact us on our website : www.autonumen.com .

Some solution to solve MB Star C3 problem

Posted on September 10, 2019 by wp-admin Posted in MB Star .

One of autonumen customer had the “simdas.exe needs to close” and WIS error when running Mb Star C3 pro red multiplexer 2015.12V Dell format DAS.

Problem 1:
I had the these errors when i run MB Star diagnosis DAS:
1) simdas.exe has encountered a problem and needs to close. We are sorry for the inconvenience.

2)The WIS is not available for this system

Cause:
Improper operation

Solution:
1. simdas.exe error: You should enter DAS but not SIM software to troubleshot Mercedes
2. WIS error:
You entered WIS from DAS directly. It was incorrect. You should start WIS from desktop.

A Mercedes Benz W212 2010 with VIN 2120891A208054 owners had the problem when diagnose his model with original MB Star C3 scanner. So he consulted autonumen technician.

Problem 2:
He has got the original Benz star c3 (with original 2013.09V Star diagnosis DAS/Xentry SSD) multiplexer to diagnose and program his model. But the software pops up an error message “ZGW is not answer”. He then contact obd365 technician if it is Ok to buy the latest 2015.12V DAS/Xentry for MB Star C3 to work on this model.

Solution:
Sorry, for MB newer model, your W212 included, you should go for MB SD Connect C4 diagnostic system with newer software version. MB star C3, even original one is too old to diagnose these newer MB cars.